Correct method of car washing

When washing your car it is important that things are done in the right way and in the right order, to avoid potential damage and also to ensure that all areas are thoroughly cleaned and not overlooked or missed. lose nothing. If you regularly wash your car yourself, you may already have your own routine that works for you and your vehicle’s needs, and this is fine as long as the end result is satisfactory and, more importantly, not jeopardize anything during the routine. .

It is very easy to fall into bad habits without knowing it, which could damage your car in some way or compromise the level of results that are achieved. It’s worth reviewing your car wash routine from time to time to see if there’s anything you can change and improve, to improve the experience by increasing efficiency and improving or refining the bottom line.

For starters, before you get near your car, it makes sense to get all the products and equipment you’ll need out and ready to go. Hoses and pressure washers should be connected to the water supply and untangled enough to provide you with enough length to comfortably reach around your vehicle. Wash buckets should be filled with shampoo and have sand guards inserted, washing implements/drying towels should be kept on hand along with any other cleaners such as wheel cleaners and all-purpose cleaners, and any cleaning brushes that may be necessary must be joined. .

These items can add up quickly, so it’s a good idea to get something that can be used to carry them and store them in a clean, safe place while you wash them. There are many such items available, ranging from designated detail bags and caddies that can be attached to your buckets, to simple soft material tool bags that can be easily converted into a ‘detail bag’. Finally, before washing it, you must make sure that your car is in a suitable place. This may mean moving it off the road into a driveway, raising it slightly to the curb to give some extra workspace on the side of the road if you don’t have a driveway, or in a cool, shaded area if the sun is out. It’s out.

The first stage of the car washing process should always be cleaning the wheels and wheel arches. This is because they tend to be the dirtiest and most polluted part of a car and often require some heavy duty products to clean properly. If you do this after you have washed the body and paint, you can easily recontaminate the cleaned surface with the product on the dew and dirt.

Also, wheels can often take a while to clean thoroughly, especially if they are very dirty or have a detailed design, so it makes sense to pay attention to these undersides early in the process. It is also advisable that you use a separate wash bucket and wash implements for the wheels and wheel arches/wells and that you do not use these items to clean other parts of your car, especially the paint, as they can become heavily contaminated with dirt and debris. grit that can easily inflict damage.

Once the wheels and arches/holes have been sufficiently cleaned, you can pre-clean/rinse the car with a suitable product, such as a traffic film remover or snow foam type product, to remove the more dirt and loose contaminants. possible before contact washing. Using a pump sprayer, hose, or pressure washer with a suitable attachment, you should generously soak at least the lower third of the vehicle, ideally the entire vehicle if possible, until the dirt visibly softens and begins to lift off the surface. surface before thoroughly cleaning. rinsing it with a pressure washer or hose. Pre-cleaners should be applied to a dry but cool car as they can adhere better to the surface and remove dirt and contaminants more effectively than if applied to a wet surface.

Once as much of the loose dirt and contaminants have been removed from the lower areas and the entire car has been thoroughly rinsed, the actual contact wash can begin. Using the two-bucket method, you want to start at the top, cleaning one section at a time, and methodically work your way down. The roof, windows, and pillars should be washed first before moving on to the hood and trunk. After washing these top areas, you should move on to the sides of your car cleaning just the top half of the doors, wings, and fenders. The fountain and upper rear halves can be washed before finally moving on to all the lower areas of the car. When washing the lower areas, it is advisable to use a separate washing implement to prevent the one used in the upper areas of the body from becoming contaminated with particles of dirt and sand, and care must be taken to stick only to the lower part. areas and do not drift up the body and over areas that have already been washed.

After you have washed all the areas, you can give the car a good rinse with a hose or pressure washer. Once again, you should start at the top and methodically work your way down to the lower areas, including the final rinse of the wheels and arches/wells, making sure to remove all suds and shampoo residue. You should note that if you are working in the heat you should wash, then rinse one section at a time to prevent the car wash solution from drying on the surface and causing unsightly streaks, then after the Last panel, the entire vehicle should be thoroughly rinsed to ensure the car is wet before drying.

After pre-cleaning, washing and rinsing, you should properly dry your car with a high-quality microfiber towel rather than a chamois to prevent damage and swirl marks from occurring. A spray lubricant/drying aid can be lightly applied to the drying towel and wet vehicle surface to help improve the finish and prevent water spots, if desired. Again, as with the other parts of the car wash process, drying should be done from the top down, one section at a time working methodically and ensuring all sections are covered, drying only the bottom parts. of the car at the bottom. final.

After all areas have dried completely, the car wash process is complete and your vehicle is ready for other cleaning and detailing processes, such as polishing and protecting, or you can just leave it at that if it’s just a car wash. regular maintenance. By following this entire process using the correct equipment and products, you should be able to easily achieve great quality results in the most efficient manner, without inflicting any damage to your car.